Hydro jetting in Marietta, Georgia uses pressurized water, not cutting blades, to strip grease, tree roots, and sludge from the inside of your sewer pipe. If your drains are slow, gurgling, or backing up into the basement, a hydro jetting service in Marietta, Georgia clears the line completely instead of just poking a hole through the blockage. We serve homeowners and businesses across Cobb County with same-day appointments and upfront pricing.
Hydro jetting in Marietta, Georgia is a drain and sewer cleaning method that pushes water at 3,000 to 4,000 PSI through a flexible hose fitted with a specialized nozzle. The nozzle fires water backward to pull itself down the pipe while forward jets scour the walls. That scouring action removes grease, sludge, sand, and tree roots that a cable machine only punches through. We feed the hose through an existing cleanout, so there is no digging in your yard. Most residential lines run 4 to 6 inches in diameter, and our equipment is sized to clean them without stressing the pipe walls.
Marietta's older neighborhoods have a mix of cast iron, clay tile, and Orangeburg pipe, and those materials collect buildup differently than modern PVC. Grease from decades of kitchen use hardens into a ring inside cast iron. Clay tile joints separate and let roots slip in. If you have been searching for hydro jetting near me in Marietta GA because snaking only bought you a few months, the problem is buildup on the pipe walls, not a single clog. Hydro jetting for sewer clogs in Marietta, Georgia removes the whole layer so flow returns to the pipe's original diameter.
Every hydro jetting job includes the camera work, the jetting itself, and a verification pass. If we find something jetting cannot fix, we tell you and quote the repair separately. Here is what you get when you book us.
We run a sewer camera or push rod camera through the cleanout and record the line. You see the footage. We identify pipe material, blockage type, and any damage that would make jetting unsafe, like a collapsed section or failing Orangeburg pipe.
We feed the hydro jetter hose through the cleanout and clean the line in controlled passes at 3,000 to 4,000 PSI. Grease, roots, sand, and sludge flush downstream or into our vacuum truck. Most residential lines take 45 to 90 minutes.
We run the camera again after jetting to confirm the pipe is at full diameter. If buildup remains, we make another pass at no extra charge. You get a clear before-and-after picture of your line's condition.
We replace the cleanout cover and make sure it seats properly. A broken cleanout is a common source of stormwater infiltration and a code issue. If yours is damaged, we can install a new one during the same visit.
Sewer work is messy. We lay down protection, rinse the area, and haul away debris. When we leave, your yard, basement, or kitchen looks the way it did before we arrived, minus the backup.
You get a summary of what we found, what we cleaned, and what to watch for. If the camera showed cast iron corrosion, clay pipe joint separation, or a sagging or bellied pipe, we note it so you can plan ahead instead of getting surprised later.
We pull the cleanout cover and run a sewer camera or push rod camera down the line. You watch the monitor with us. We note pipe material, diameter, blockage location, and any cracks, bellies, or root masses. This takes 15 to 30 minutes and decides whether jetting is the right call.
If the cleanout is buried or the line runs under a driveway, we use a sewer line locator transmitter to mark the path above ground. That protects your landscaping and tells us exactly where the jetting hose is going. On older Marietta properties, this step often saves an hour of guesswork.
We feed the hydro jetter hose through the cleanout and work it downstream in controlled passes. Water pressure starts lower and ramps up as the line clears. Grease and roots flush to the city main or into our vacuum truck. A typical residential line takes 45 to 90 minutes to clean.
After jetting, we run the camera again. If any section still shows buildup, we make another pass. We confirm the pipe is at full diameter and check that no joints were disturbed. You get a clear picture of the line's condition before we pack up.
We replace the cleanout cover, rinse the work area, and walk you through what we found. If we spotted cast iron corrosion, clay pipe joint separation, or a sagging or bellied pipe, we tell you now so you can plan. No surprise invoices, no pressure.
We pull the cleanout cover and run a sewer camera or push rod camera down the line. You watch the monitor with us. We note pipe material, diameter, blockage location, and any cracks, bellies, or root masses. This takes 15 to 30 minutes and decides whether jetting is the right call.
Our primary jetting machine. It delivers 3,000 to 4,000 PSI through a flexible hose and specialized nozzle to scour grease, roots, and sludge from residential and commercial lines.
Used before and after every jetting job. We record the line so you see the blockage and the result. The push rod camera handles tight turns and smaller lines where a standard camera will not pass.
For light clogs and lines that are not safe to jet, we use a cable machine. It is faster and cheaper for a single soft blockage, and we recommend it when jetting would be overkill.
When jetting flushes heavy debris, grease, or root mass, the vacuum truck captures it instead of sending it down the city main. It also handles cleanup on large commercial jobs.
Traces the pipe path above ground before we jet or dig. This protects landscaping and driveways and tells us exactly where the line runs on older lots with unpermitted additions.
When jetting confirms a line is too damaged to clean or line, we replace it by pulling new HDPE pipe through the old one. Minimal digging, same diameter, long service life.
A homeowner on the east side had backups every spring for three years. Snaking cleared it each time, but roots returned within months. The camera showed a 4-inch clay tile line with root masses at four joints and 60 percent flow restriction.
After: We jetted the line in two passes, cut the roots back to the pipe wall, and flushed the debris. Post-jetting camera showed full-diameter flow. We sealed two joints and lined one section. Fourteen months later, no backups.
Book this service →
A restaurant had grease backing into the kitchen floor drain every three to four weeks. Snaking cleared it for a week or two. The line was 40 percent blocked with hardened grease and food solids along the pipe walls.
After: We jetted the line at night in two passes, then ran the camera to confirm full-diameter flow. We set up a quarterly jetting schedule. Six months in, the line has not backed up once and the health inspector has current maintenance records.
Book this service →
A homeowner in West Marietta had slow drains throughout the house and one backup in the laundry room. The camera showed heavy cast iron corrosion and scale narrowing a 4-inch line to roughly 2.5 inches in places.
After: We jetted the line to remove the scale and restored flow. The camera showed the pipe at nearly full diameter, but the corrosion was advanced. We quoted a spot replacement on the worst 12-foot section, which the homeowner scheduled for the following month.
Book this service →Most sewer calls come down to a handful of problems. Jetting fixes some of them permanently and buys time on others. Here is what we see most often in Marietta and how we handle each one.
Ask a pro →We jet the line at 3,000 to 4,000 PSI to strip the grease ring back to bare pipe. For restaurants on Delk Road and Powers Ferry, we set up quarterly jetting schedules so grease never gets a chance to harden.
We cut the roots with the jetter and flush them out, then note the entry points on camera. If roots are a recurring problem, we seal the joints or line that section with CIPP so roots cannot get back in.
Hydro jetting for sewer clogs in Marietta, Georgia removes the buildup instead of cutting through it. Most customers who switch from snaking to jetting go a year or longer between service visits, which pays for the difference.
We jet the line clear, then check your backwater valve. If you do not have one, we install and test it so the next storm stays in the street where it belongs. This is one of the highest-value fixes we do.
$350 - $750 for most residential jobs; $600 - $1,500+ for commercial lines
Typical 2026 pricing for residential hydro jetting in Marietta runs $350 to $750, including the camera inspection before and after. Commercial lines, heavy root masses, and long runs cost more. We quote the number before we start, and the price covers the camera work, jetting, verification, and cleanup. If the camera shows a problem jetting cannot fix, we stop and quote the repair separately. No surprise line items on the invoice.
Hydro jetting costs more than a single snaking, but it usually ends the cycle of repeat clogs. If you have paid for three snakings in a year, jetting often costs less than the next two calls combined, and it leaves you with camera footage of your line.
A standard 40- to 60-foot residential lateral is straightforward. Longer runs, or lines where the cleanout is buried or missing, add time and sometimes require a cleanout installation first.
Get a quote ↗Light grease is quick. Heavy root masses, hardened grease rings, and sludge that fills the pipe take multiple passes. A fully blocked 4-inch line can take twice as long as a partially blocked one.
Get a quote ↗PVC and sound cast iron jet quickly. Clay tile with separated joints needs lower pressure and more care. Orangeburg pipe cannot be jetted at all, so we quote replacement instead.
Get a quote ↗Commercial kitchen lines carry heavier grease loads and often run longer distances. They take more time and equipment, and many customers choose a quarterly maintenance plan that lowers the per-visit cost.
Get a quote ↗Most residential hydro jetting jobs in Marietta run $350 to $750 in 2026, including the camera inspection before and after. Commercial lines, heavy root masses, and long runs push the price higher. If the camera shows a collapsed sewer line or failing Orangeburg pipe, jetting is not the answer and we will quote repair instead. We give you the number before we start.
Yes, for sound pipes. We run a camera first and adjust pressure to the pipe material. PVC, ABS, cast iron, and HDPE handle 3,000 to 4,000 PSI without issue. We do not jet clay tile with separated joints, Orangeburg pipe, or any line showing collapse. On those, we recommend repair or lining. The camera pass is what makes jetting safe, and it is included in every job.
It does. The nozzle cuts roots back to the pipe wall and flushes the debris downstream. On a 4-inch line with moderate root intrusion, one pass usually restores full flow. Heavy root masses may need two passes. Jetting does not stop roots from returning, so we note the entry joints on camera and can seal or line them to keep roots out long term.
A drain snake auger cuts a channel through the clog. Water flows again, but grease and roots remain on the pipe walls and regrow. Hydro jetting scours the full pipe diameter, so the line stays clear longer. Snaking is faster and cheaper for a single soft clog. Jetting costs more upfront but usually ends the cycle of repeat backups, which is why most of our customers switch.
Slow drains and backups get worse, not better. We are licensed, insured, and local, and we bring a camera to every job so you see exactly what is in your line. Call now for same-day hydro jetting in Marietta, Georgia and get your sewer flowing again.
Book Hydro Jetting +14707391979 →Reach out for fast, friendly service. We're available 24/7 for emergencies and can schedule regular appointments Monday through Friday. Call us at +1 470-739-1979 or email info@mariettsewersolutions.com. We serve all of Marietta and surrounding areas.